YardMath — How much material do you need? Calculate it in seconds.

Free calculators for American homeowners, DIYers and small contractors. Enter your measurements, get cubic yards, bags, gallons, tons and cost — with waste allowances built in, formulas explained, and every number checked against manufacturer datasheets.

All 22 calculators

Popular

Concrete Calculator

Cubic yards, 40/60/80 lb bags and cost for slabs, footings and columns.

Open calculator →
Popular

Square Footage Calculator

Add rooms, split L-shaped spaces and get total square feet or square meters.

Open calculator →
Popular

Mulch Calculator

Cubic yards and bags for rectangular, circular and ring-shaped beds.

Open calculator →
Popular

Gravel Calculator

Yards, tons and bags by stone type, from driveways to decorative beds.

Open calculator →

Flooring Calculator

Boxes, underlayment rolls and cost, with a waste slider for your layout.

Open calculator →

Tile Calculator

Tile count, grout bags and waste for any tile size and joint width.

Open calculator →

Paint Calculator

Gallons needed per coat for walls and ceilings, minus doors and windows.

Open calculator →

Fence Calculator

Posts, rails, boards and concrete bags for privacy fences of any length.

Open calculator →

Drywall Calculator

Sheets, screws, tape and joint compound for rooms, including ceilings.

Open calculator →

Topsoil Calculator

Cubic yards, 40 lb bags and tons of topsoil for lawns and garden beds.

Open calculator →
Popular

Sod Calculator

Rolls, pallets and cost for any lawn size — one roll covers 10 sq ft.

Open calculator →
Popular

Deck Calculator

Decking boards, joists, posts, screws and concrete for any deck size.

Open calculator →
Popular

Roofing Calculator

Roof area by pitch, squares, shingle bundles, underlayment and drip edge.

Open calculator →

Wallpaper Calculator

Rolls needed for any wall, minus doors and windows, with pattern waste.

Open calculator →

Insulation Calculator

Bags needed for attics and walls by R-value, with thickness and cost.

Open calculator →

BTU Calculator

The right air conditioner size for any room — BTUs and tons.

Open calculator →

Lumber Calculator

Studs, plates, linear feet and board feet for wall framing.

Open calculator →

Deck Stain Calculator

Gallons of stain for new wood or recoats, by coats and coverage.

Open calculator →

Concrete Block Calculator

8×16 in blocks, mortar bags and core-fill concrete for any wall.

Open calculator →

Rebar Calculator

#3, #4 and #5 bars, total length, weight and 20-ft bar count.

Open calculator →

Sand Calculator

Cubic yards, tons and 50 lb bags for patios, paver bases and play areas.

Open calculator →

Asphalt Calculator

Tons, 50 lb cold-patch bags and cost for driveways and overlays.

Open calculator →

How it works: three steps

1

Measure the space

Length, width and thickness or depth — one tape measure is the only tool you need. Our guides show where to measure for every shape, including L-shaped rooms and ring beds.

2

Enter the numbers

Type them into the calculator. Results update as you type: volume, bag count, tonnage and cost, with a waste allowance slider set to the right default for your project.

3

Buy with confidence

Copy the results, print them, or share the link — your numbers travel in the URL. Hand the list to the store, or price it against bulk delivery quotes.

Every calculator runs entirely in your browser. Nothing is uploaded, nothing is stored on a server, and your last unit preference is remembered on your own device.

Popular quick answers

ConcreteCommon slab sizes (4 in thick, 10% waste)

80 lb bag counts for frequent pours
SlabExact volumeOrder volume80 lb bags
10 × 10 ft patio1.23 cu yd1.36 cu yd62
12 × 12 ft shed pad1.78 cu yd1.95 cu yd88
10 × 20 ft one-car drive3.09 cu yd3.40 cu yd153
20 × 20 ft two-car drive6.17 cu yd6.79 cu yd306

MulchWhat one bag covers

Coverage per 2 cu ft bag by depth
Depth1 in2 in3 in4 in
Coverage per 2 cu ft bag24 sq ft12 sq ft8 sq ft6 sq ft
Coverage per cubic yard324 sq ft162 sq ft108 sq ft81 sq ft

Which calculator do you need?

Every project starts with one measurement question. Here is where each tool fits — and what its numbers mean when you get to the store.

Pouring or footing

The concrete calculator handles anything you pour: patios, shed pads, driveways, continuous footings and round column footings. It returns cubic yards (what ready-mix trucks deliver) and bag counts for 40, 60 and 80 lb mixes (what the store sells), plus estimated weight so you know whether you are wheelbarrowing a ton or ordering a truck. Strength, not volume, is the other half of the order — the page includes a PSI guide by project type.

Floors, walls and rooms

Start with the square footage calculator if you need a plain area total — it sums room-by-room and handles L-shaped spaces as two rectangles. From there, the flooring calculator converts area into boxes, underlayment rolls and transition strips with a waste slider for your layout; the tile calculator counts pieces using the true laying pitch (tile plus grout joint) and estimates grout bags; and the paint calculator walks the perimeter, subtracts doors and windows, and returns gallons per coat — ceiling and primer included when you need them.

Walls going up or covered

The drywall calculator is a full material list for hanging and finishing: sheets by board size, screws, joint tape and gallons of compound, with doors and windows deducted. Pair it with the paint calculator when the room is finished — the same room dimensions feed both. For the structure behind the drywall, the lumber calculator counts studs, plates and board feet for any wall at 12, 16 or 24 in spacing; the concrete block calculator sizes 8×16 in block walls with mortar bags and core-fill concrete; and the rebar calculator sizes the steel grid inside slabs and footings by bar size and spacing. On the finished side, the wallpaper calculator returns single and double roll counts after deducting doors and windows, and the insulation calculator sizes bags by R-value for attics and walls.

Roofs, decks and comfort

The roofing calculator turns a footprint and pitch into roof area, squares, shingle bundles, underlayment rolls and drip edge, with a waste allowance for valleys and hips. Outside, the deck calculator produces the full build list — boards, joists, posts, screws and footing concrete — and the deck stain calculator follows up with gallons for new wood or recoats. And when the room is finished, the BTU calculator sizes the air conditioner for it, adjusting the 20 BTU per square foot rule for sun, ceiling height, people and kitchens.

Outside: beds, stone and soil

Yard materials all share one volume shortcut — (square feet × inches of depth) ÷ 324 = cubic yards — but they are sold differently. The mulch calculator outputs bags of 2 and 3 cu ft plus bulk yards, with a ring mode for around trees; the gravel calculator adds stone-type density to return tonnage, because gravel sells by the ton; and the topsoil calculator converts depth of loam into yards, 40 lb bags and approximate truckload weight. The sod calculator does the same job for lawns — rolls and pallets by lawn area, with a waste allowance for cutting; the sand calculator covers paver bases and play areas in cubic yards, tons and 50 lb bags; and the asphalt calculator sizes driveways and overlays in tons and cold-patch bags. For anything vertical, the fence calculator produces the full build list: posts with gate posts added, rails, pickets at their true pitch, and the concrete to set every post.

Mixed projects

Real projects chain several tools: a backyard makeover might run square footage, then mulch for the beds, gravel for the path, concrete for the pad and fence for the perimeter. Every calculator links to its siblings at the bottom of the page so you can move through the project without losing your numbers.

About this site

YardMath is built and maintained by a small editorial team with construction and DIY backgrounds, for the most common question in American home improvement: how much do I buy? Every calculator is free, runs entirely in your browser (your measurements never leave your device), and shows the formula behind the result so you can check it, adapt it, or argue with it. Pages carry a last-reviewed date, formulas are tested against hand-worked examples before publication, and price information is written as dated ranges — never as quotes. Details, sourcing and our review process are on the About page; what the results are and are not is on the disclaimer page.

Units, rounding and how the numbers are checked

Every calculator on this site follows the same three conventions. First, quantities are shown exact and then rounded: the volume or area you need is printed to two decimals, and the things you actually buy — bags, boxes, boards, gallons, tons — are rounded up to whole units, because nobody sells 0.61 of a bag. Second, waste is a choice, not a constant: each tool starts at a sensible default (10% for most materials) and always shows the raw number next to the adjusted one, so you can see exactly what the allowance is costing you. Third, cost lines round the purchase quantity the way suppliers bill it — whole cubic yards for bulk material, whole tons for gravel, whole sheets, boxes and bags for building materials — and every price field is optional: leave a price blank and the cost rows simply disappear.

Checking works the same way on every page. Each formula was tested against a hand-worked example — 46 cases across the 22 tools — against manufacturer coverage charts for bagged goods and paint, and against supplier density tables for gravel and stone. The worked example printed on each page shows the arithmetic step by step, so if a result ever looks wrong, the fastest check is to redo that page’s example by hand with the same inputs.

What you can safely change: every waste box, every price field, every unit toggle. What you should not change: the depth minimums printed on each page (a 2-inch mulch layer starves soil life as surely as a 1-inch gravel base ruts), and the rounding direction — the site rounds purchases up on purpose, because a half-bag short is a second trip to the store and a half-yard short is a minimum-load delivery fee. When a default does not fit your trade or your region, change it, run it, and the URL keeps the whole scenario for the supplier to see.

One honest boundary: estimating material is arithmetic, and this site does it well; designing structure is engineering, and this site does not try. Anything load-bearing, anything below grade, anything with a permit attached — use the numbers here to budget and plan the order, then confirm the specification with the local supplier, contractor or engineer who has actually seen the site.

Are the calculators really free?

Yes — all of them, all the time, with no usage caps, no accounts, no watermarks on printed results and no premium tier. The site is supported entirely by clearly separated advertising, which never sits between an input and its result. If a calculator ever asks you for an email address or a payment to show a number, it is not ours.

How we calculate (and how we check)

YardMath's formulas are the standard ones the trade uses, and every constant on the site is traceable:

  • Bag yields come from manufacturer datasheets — 80 lb concrete yields 0.60 cu ft, 60 lb yields 0.45, 40 lb yields 0.30.
  • Densities for gravel and soil are typical quarry and extension-service averages, stated openly on each page with a custom override where it matters.
  • Coverage tables (grout, paint, mulch) approximate published manufacturer charts and are labeled as approximations.
  • Material constants for the newer tools are the standard trade figures, stated on each page — one sod roll covers 10 sq ft and one pallet 500; three shingle bundles make one square; #4 rebar weighs 0.668 lb/ft; asphalt runs 145 lb per cu ft and sand about 2,700 lb per cu yd.
  • Prices are national planning ranges checked November 2026 — always labeled as ranges, never quotes, because regional pricing swings hard.

Pages are reviewed by the YardMath Editorial Team and re-checked quarterly; each page shows its last-reviewed date. Results are estimates for planning — confirm quantities with your supplier and get permits and professional input for structural work. See our About page for methodology details, the disclaimer for what these numbers are and are not, and the privacy policy for how little we collect (spoiler: no accounts, no tracking beyond standard analytics).